A toilet that keeps running after you flush is one of the most common — and most wasteful — problems in a small home. You hear the faint hiss of water, the tank refills every few minutes, and the cistern never quite settles. It is easy to ignore because the toilet still flushes, but a toilet that runs non-stop can waste up to 750 litres of water a day — more than a family of four uses for drinking, cooking and washing in a week. On a metered water bill, that leak can add $30 to $60 a month.
Fix a running toilet by finding the one part that has failed — in 9 out of 10 cases it is the flapper, the chain, or the fill valve — and replacing or adjusting it. You need no plumber, no special tools beyond an adjustable wrench, and about 30 minutes. This guide walks you through the diagnosis first, then the three fixes in order of likelihood, so you only replace the part that is actually broken. No plumbing experience needed, and every part costs under $15.
Quick Answer: A running toilet is caused by a worn flapper that no longer seals, a chain that is too short, or a fill valve set too high. Check the water level — it should sit 2.5 cm below the overflow tube — then run the food colouring test. Most fixes take under 30 minutes and cost less than $15.
Key Takeaways
- A running toilet can waste up to 750 litres of water a day, so fixing it is the cheapest water-saving job in the house.
- The food colouring test tells you in 10 minutes whether the leak is in the flapper or the fill valve.
- The flapper is the culprit in most cases — a $5 part that takes 10 minutes to replace.
- The chain needs about 12 mm of slack: too tight and the flapper never seals, too loose and the flush is weak.
- If the water level sits above the overflow tube, the fill valve is set too high and needs adjusting, not replacing.
Table of Contents
- Diagnose First: Find the Leak Before You Buy Parts
- Fix the Flapper: The Most Common Cause
- Fix the Fill Valve: When the Tank Keeps Refilling
- Check the Overflow Tube and Flush Valve Seat
- How Much Water and Money a Running Toilet Wastes
- Your Running Toilet Checklist
- Where Should You Start?
- Frequently Asked Questions
Diagnose First: Find the Leak Before You Buy Parts
Never buy parts before you know which one has failed. A running toilet has only three possible causes, and two simple tests separate them in about 10 minutes. Do the tests in order, and write down what you find — the result tells you exactly which section of this guide to follow.
1. Do the food colouring test (10 minutes, no tools)
Lift the tank lid and add 10 drops of food colouring — or a strong cup of tea or coffee — to the water in the tank, then do not flush for 10 to 15 minutes. If colour appears in the toilet bowl, water is leaking from the tank into the bowl past the flapper, so the flapper or its chain is the problem. If the bowl stays clear but the tank keeps refilling, the fill valve is the problem — water is escaping down the overflow tube instead. This one test saves you buying the wrong part, and it costs nothing. Our drain and leaky faucet guide uses the same test-first approach before any repair, and you can browse every fix on the Home Fixes category page.
2. Check the water level — 2.5 cm below the overflow tube
With the tank full and settled, look at the water line against the overflow tube — the tall open pipe standing in the middle of the tank. The water should sit about 2.5 cm (1 inch) below the top of that tube. If the water is at or above the tube's rim, water is constantly spilling into it, and the fill valve is set too high or has failed. If the level is correct but the toilet still runs, the leak is almost certainly the flapper. Mark the correct level with a pencil on the inside of the tank so you can check it again after the repair.
3. Listen and look for the exact failure
Take the tank lid off, flush once, and watch the whole cycle. A flapper that lifts and drops back crookedly, or that wobbles and never sits flat, is worn or warped. A chain that catches on the flapper arm or kinks will hold the flapper open a crack. A fill valve that keeps hissing after the tank is full has a worn seal inside. Run your finger around the flapper — if it feels rough, warped or slimy, it has perished and will not seal again no matter how you clean it. This two-minute watch tells you more than any guesswork, and it costs nothing.
Fix the Flapper: The Most Common Cause
The flapper is the rubber disc at the bottom of the tank that lifts when you flush and drops back to seal the tank. It is the part that fails most often, because rubber perishes in water over 3 to 5 years. If your food colouring test showed colour in the bowl, start here.
4. Clean the flapper seat and test it again
Turn off the water supply at the small valve behind the toilet, flush once to empty the tank, and lift the flapper off its pegs. Wipe the flapper and the round seat it sits on with a cloth — mineral deposits and slime often stop a good flapper sealing. Put it back, turn the water on, and repeat the food colouring test. If the leak stops, you have fixed it for free in 10 minutes. If colour still appears in the bowl, the flapper itself is worn and needs replacing — cleaning cannot fix rubber that has gone hard or warped.
5. Replace the flapper — a $5 part, 10 minutes
Take the old flapper to the hardware shop, or measure its diameter: most are 5 cm (2 inch) or 7.5 cm (3 inch). Buy a universal flapper of the same size for about $5. Turn off the water, flush to empty the tank, unhook the old flapper from its two pegs and unclip the chain, then hook the new one on in exactly the same way. Clip the chain to the flush lever arm with about 12 mm (half an inch) of slack — enough that the chain hangs in a slight curve, not pulled tight. Turn the water back on, let the tank fill, and repeat the food colouring test to confirm the seal. If you can buy a flapper with an adjustable float, it lets you fine-tune the flush strength later.
6. Fix the chain — 12 mm of slack, no tangles
A chain that is too short holds the flapper open a crack, so the toilet runs forever. A chain that is too long tangles under the flapper and stops it sealing. The right length leaves about 12 mm of slack when the flapper is closed — move the clip one link at a time until the chain hangs in a gentle curve. Check that the chain cannot slip under the flapper when it drops, and that it does not catch on the overflow tube. This is a two-minute fix that solves a surprising number of running toilets on its own, and it costs nothing.
Fix the Fill Valve: When the Tank Keeps Refilling
The fill valve is the tall valve on the left of the tank that refills it after a flush. If your food colouring test was clear but the toilet keeps running, or the water level sits above the overflow tube, the fill valve is the problem.
7. Adjust the float to lower the water level
Most fill valves have a float — either a ball on an arm or a cup that slides on the valve body. To lower the water level, bend the ball arm gently downwards, or turn the adjustment screw on the top of the valve clockwise, or squeeze the clip on the float cup and slide it down about 2.5 cm. Flush and let the tank refill, then check the level again against the overflow tube: it should stop about 2.5 cm below the rim. Repeat until the fill stops at the right level. If the valve keeps running even at the lowest setting, its internal seal is worn and the valve needs replacing, not adjusting.
8. Replace the fill valve — $10 to $15, 30 minutes
Turn off the water supply and flush to empty the tank, then sponge out the last of the water. Unscrew the water supply hose from the bottom of the fill valve, then undo the lock nut underneath the tank and lift the old valve out. Set the new valve's height so its top sits about 2.5 cm above the overflow tube, drop it in, tighten the lock nut by hand plus a quarter-turn with a wrench, and reconnect the supply hose. Clip the small refill tube into the top of the overflow tube so it points down inside it, turn the water on, and adjust the float until the level stops 2.5 cm below the overflow rim. A universal fill valve costs $10 to $15 and fits almost every toilet — take a photo of your old valve before you shop, so you can match the height and connection.
Check the Overflow Tube and Flush Valve Seat
Two smaller causes are worth checking if the flapper and fill valve are both fine. They are quick to rule out, and they explain the stubborn cases that keep running after a new flapper.
9. Check the overflow tube height and the refill tube
The overflow tube should stand about 2.5 cm below the tank's rim — if it was cut too short or cracked, water pours into it constantly. Look for a crack near its base; a cracked tube can be replaced for a few dollars, but it usually means replacing the whole flush valve. Also check the thin refill tube from the fill valve: it must point down inside the overflow tube, not dangle outside it. If it sits outside, the water it delivers misses the bowl refill and the tank overfills instead. Push it back into its clip so it aims straight down the tube.
10. When the flush valve seat is damaged
If a brand-new flapper still leaks, the seat it sits on — the round rim at the bottom of the tank — may be pitted or rough. Run your finger around it: if it feels rough or you can see chips, smooth it gently with fine sandpaper (400 grit) and try again. If the seat is cracked or badly corroded, the whole flush valve needs replacing, which is a bigger job — about an hour and a $20 part — and a reasonable point to call a plumber if you are not comfortable removing the tank. Our monthly home maintenance checklist includes a yearly toilet check so you catch a worn flapper before it starts wasting water.
How Much Water and Money a Running Toilet Wastes
The numbers are what make this repair worth doing today, not next month. Here is what a single running toilet costs on a typical home:
| Leak | Water wasted per day | Water wasted per month | Extra cost per month* |
|---|---|---|---|
| Slow leak, flapper weeping | 100 litres | 3,000 litres | $5–$10 |
| Steady run, fill valve stuck | 400 litres | 12,000 litres | $15–$25 |
| Full run, water pouring into overflow | 750 litres | 22,500 litres | $30–$60 |
| Repair cost (flapper + chain) | $5–$8 | — | Pays for itself in days |
*Based on typical metered water rates of about $2 per 1,000 litres; your rate may differ, but the waste is the same. A $5 flapper that stops a 750-litre-a-day leak saves roughly 22,500 litres a month — more water than a family of four drinks in a year. Even the slow weeping leak wastes 3,000 litres a month, which is 36,000 litres a year. If you are on a water meter, check your bill after the repair: a sudden drop confirms the fix worked.
Your Running Toilet Checklist
Work through this list in order and tick each step off as you finish it:
- ☐ Lift the tank lid and note the water level against the overflow tube (should be 2.5 cm below the rim)
- ☐ Add food colouring to the tank and wait 10–15 minutes without flushing
- ☐ If colour reaches the bowl, clean the flapper and its seat, then test again
- ☐ If it still leaks, replace the flapper ($5, 10 minutes) and set the chain to 12 mm of slack
- ☐ If the bowl stayed clear, adjust the float until the water stops 2.5 cm below the overflow tube
- ☐ If the valve still runs, replace the fill valve ($10–$15, 30 minutes)
- ☐ Check the refill tube points down inside the overflow tube, not outside it
- ☐ Run the food colouring test one last time to confirm the leak is gone
- ☐ Listen for 5 minutes — no hiss, no refill, no running water
- ☐ Check the next water bill for the drop, and add a yearly toilet check to your maintenance routine
- ☐ Put the tank lid back on straight, so it does not press on the flush lever
- ☐ Keep the old flapper and the part number, so the next replacement takes 5 minutes
Where Should You Start?
Start with the food colouring test today — it takes 10 minutes, costs nothing, and tells you exactly which part has failed. Do not buy a flapper until you know the flapper is the problem, and do not replace the fill valve until you have tried adjusting the float. In 9 out of 10 cases, a $5 flapper and 12 mm of chain slack is the whole repair, and the toilet will be silent by tonight.
And once the toilet is fixed, look at the rest of the water in your home: our drain and leaky faucet guide fixes the other two common water wasters, and you can browse every fix on the Home Fixes category page.
Frequently Asked Questions
How do I know if my toilet is running?
Listen for a faint hiss or trickling sound from the tank, or watch for the tank refilling on its own every few minutes. The surest test is food colouring: add 10 drops to the tank water, wait 10 to 15 minutes without flushing, and if colour appears in the bowl, water is leaking past the flapper. A toilet that runs can waste up to 750 litres a day, so even a quiet leak is worth finding.
How much does it cost to fix a running toilet?
Most running toilets cost under $15 to fix. A universal flapper is about $5 and takes 10 minutes to fit, a new fill valve is $10 to $15 and takes about 30 minutes, and adjusting the float or the chain costs nothing. Only a damaged flush valve seat is more expensive — about $20 for the part and an hour of work — and that is the point where calling a plumber starts to make sense.
Can I fix a running toilet without turning off the water?
You can diagnose it and adjust the chain or the float with the water on, but always turn off the supply valve behind the toilet before replacing the flapper or the fill valve. Flushing once after turning it off empties most of the tank, and a sponge takes out the rest. Working with the water on risks a flood if a hose slips, so take the 30 seconds to turn it off.
How often should I replace a toilet flapper?
Every 3 to 5 years, or sooner if the food colouring test shows a leak. Rubber perishes in water, and hard water or cleaning tablets in the tank wear it out faster. Check it once a year — the food colouring test takes 10 minutes — and replace it at the first sign of a leak rather than waiting for the toilet to start running, because a slow leak can waste 3,000 litres a month before you notice it.

Comments (0)
Post a Comment