Every small home has the same secret shame: the tangle of black cords behind the TV, the charger cables snaking across the bedroom floor, the power strip gathering dust under the desk. You can tidy the whole room, fluff the cushions and wipe every surface, and the room still looks messy — because the eye goes straight to the cables. In a small home the problem is worse, since there is nowhere for the mess to hide: the TV is two steps from the sofa, the desk sits in the corner of the bedroom, and every cord is on display.
How to hide cords and cables in a small home comes down to four moves in the right order: trace every cord and unplug what you do not need, bundle what is left, cover the runs along the wall, and box the power strips out of sight. The whole job costs about $29, takes one afternoon, and needs no drilling, no electrician and no landlord permission — every fix in this post peels off or lifts away when you move out. Here are 12 ideas, room by room, starting with the five-minute audit that tells you exactly what you are dealing with.
Quick Answer
Start with a cord cover: a paintable plastic raceway hides a whole TV cable run for about $8 and takes ten minutes to stick on. Bundle the rest with velcro ties, drop power strips into a $12 cable box, and clip phone chargers to the desk edge. The full tidy-up costs about $29 and one afternoon.
Key Takeaways
- Trace every cord before you buy anything — most tangles are two or three cables doing the same job.
- A paintable cord cover is the fastest fix: it hides a whole TV run for about $8 in ten minutes.
- Power strips belong inside a cable box, not on the floor — it is safer and looks instantly tidy.
- Velcro ties beat zip ties for anything you unplug often, and they cost pennies each.
- Paint the cord cover the same colour as the wall and it disappears — matching beats camouflage every time.
Table of Contents
Start With the Worst Tangle First
Do not buy a single cord cover until you know what you are hiding. Most cable messes look bigger than they are: a "hopeless" tangle behind the TV is usually five cables, and two of them belong to devices nobody uses any more. Ten minutes of tracing first saves you buying the wrong size box and the wrong length of cover.
1. Trace every cord and label both ends
Pick the worst spot — usually the TV or the desk — and follow each cord from the device to the plug with your finger, one at a time. As you trace it, stick a small label on both ends: a strip of masking tape with "TV", "router" or "lamp" written on it costs nothing and saves you unplugging the wrong thing later. You will almost always find a surprise: a cable for a games console that left the house months ago, a phone charger for a phone you no longer own, or two chargers doing one job. Unplug the dead ones and put them in a bag — the tangle often shrinks by a third before you have spent a cent. Keep the labels on: the next time a cable fails, you will know in seconds which one to replace instead of pulling the whole bundle apart.
2. Unplug what you do not use every day
A cable that is plugged in but unused is still clutter, and it still draws a little standby power. Walk the home with a simple rule: if a device has not been switched on in the last two weeks, unplug it and coil its cable with a velcro tie. The DVD player, the spare monitor, the old printer and the second lamp by the sofa are the usual suspects. Store the coiled cables in one labelled box in a cupboard, not loose in a drawer where they tangle into a knot that takes twenty minutes to undo. For devices you use weekly but not daily — a games console, a printer, a hair dryer — keep the cable coiled beside the device and plug it in only when you need it. Fewer live cords means fewer cords to hide, and the ones that remain are the ones that earn their place.
Hide Cords Along Walls and Floors
Once only the working cords remain, the job is to get them off the floor and along the edges of the room, where the eye never looks. Cords that run in straight lines along a skirting board or a door frame look intentional; cords that sag across open floor look like a mess, and they are a trip hazard too.
3. Stick a paintable cord cover along the skirting board
A cord cover — also called a raceway — is a slim plastic channel with a snap-on lid that sticks to the wall with adhesive tape. You lay the cables inside it, snap the lid on, and the whole run disappears into a neat white strip. A 1-metre length costs about $8, cuts to size with a kitchen knife, and takes ten minutes to fit: peel the backing, press it along the skirting board from the TV to the socket, tuck the cables in and clip the lid on. The trick that makes it vanish is paint: the covers are made to be painted, so one coat of the same paint as the wall makes the strip almost invisible from across the room. Run it tight along the skirting board, not diagonally up the wall, and use a corner piece where the wall turns — a diagonal run is the one thing that still catches the eye.
4. Run cables behind furniture, not in front of it
The cheapest cord cover in the world is a piece of furniture. Before you buy anything, look at the gap between the TV stand and the wall, or between the sofa and the skirting board: most small homes have a 5 cm channel there that swallows a whole cable run for free. Push the TV stand 3 cm closer to the wall, drop the cables behind it, and let the stand itself hide them. The same trick works behind a bedside table, a desk pushed against the wall and a bookshelf: route the cables down the back of the furniture instead of letting them hang in the gap at the side. The rule is simple — if you can see a cable from the doorway, move the furniture, not the cable. Just leave a little slack in each cord so the plug is never pulled tight, and never trap a cable under a heavy piece of furniture where it can be crushed and overheat.
5. Use a flat floor cord cover where cables must cross a walkway
Some cables have to cross open floor — a lamp on the far side of the room, a router that only works in one corner — and a loose cable across a walkway is a trip waiting to happen. A flat floor cord cover is a low rubber ramp, about 8 cm wide, that lies over the cable and lets feet and vacuum cleaners pass over it safely. One metre costs about $6, it needs no fixings, and it works best run tight against a wall or under the edge of a rug so nobody steps on it at all. For a short crossing, a rug does the same job for free: run the cable under the rug in a straight line, tape it flat to the floor first with gaffer tape so it cannot bunch up, and the rug hides it completely. Never run a cable under a rug without taping it flat — a loose cable under a rug is both a trip hazard and a fire risk, because the rug traps the heat a damaged cable gives off.
Box and Bundle the Mess
The ugliest spot in most homes is not a single cable — it is the power strip, where six plugs, six cables and a transformer block pile up in one dusty heap. That heap is also the most useful thing to hide, because one box fixes the whole mess at once.
6. Drop the power strip into a cable management box
A cable management box is a ventilated plastic box, about 30 cm long, with slots in the sides for cables to enter and leave. You put the whole power strip inside it, plug everything in, thread the cables out through the slots, and put the lid on — what was a dusty heap becomes a neat box you can put a plant or a book on top of. A good one costs about $12 and fits a 6-socket strip with room to spare. Buy the size up from what you think you need: a box that is crammed full is no better than the heap it replaced, and transformer blocks — the big chunky plugs on laptop chargers — need extra room. Keep the lid loose, never sealed: the slots are there for airflow, and a power strip in a sealed box can overheat. Put the box on the floor behind the TV stand or under the desk, not on a shelf where the lid becomes another surface to pile things on.
7. Bundle cables with velcro ties, not zip ties
A bundle of five loose cables looks like a mess; the same five cables tied together every 30 cm looks like one neat cord. Velcro cable ties cost about $3 for a pack of twenty, wrap around a bundle in seconds, and — unlike plastic zip ties — they open again, so you can add or remove a cable without cutting anything. Bundle the cables that run together, from the TV to the socket or from the desk to the wall, and leave a little slack at each end so the plugs are never strained. Colour-code if you like: one colour for the TV, one for the desk, one for the bedroom — then the label on the end tells you which bundle to follow. The one place zip ties still win is a permanent run you will never touch again, like a cable fixed inside a cord cover: there a zip tie's grip is tighter, and you will never need to open it.
8. Clip charging cables to the desk edge so they stop falling
The most annoying cable in any home is the phone charger that slides off the desk and lands on the floor every single time. A small adhesive cable clip — a plastic slot that sticks to the edge of a desk or bedside table — holds the end of the cable exactly where your hand expects it. A pack of six costs about $4, sticks on in seconds, and peels off cleanly when you move. Put one clip per cable: one for the phone charger, one for the laptop charger, one for the headphones. Leave about 15 cm of cable hanging past the clip so the plug reaches the phone on the desk without pulling the clip off, and keep the clips on the side of the desk you sit at, not the front edge where your knees catch them. The same clips work on a bedside table, where they stop the charger falling behind the bed — the place cables go to die.
Make Cords Part of the Decor
Sometimes the honest answer is that a cable cannot be hidden — the lamp is in the middle of the room, or the rental rules forbid sticking anything to the wall. In those cases, stop fighting the cable and make it look deliberate instead. A cable that looks chosen is a cable nobody notices.
9. Dress a visible cable in a fabric sleeve
A cable sleeve is a fabric tube that zips or wraps around a bundle of cables and turns five black cords into one soft, tidy line. A 3-metre sleeve costs about $7 and comes in colours that match a room — sage green, cream or terracotta — instead of the black that screams "cable". It works best on a cable that hangs or drapes, like the cord from a pendant lamp or the run from a wall-mounted TV down to a low cabinet: the sleeve makes it look like a design choice rather than an accident. Choose a sleeve in a colour close to the wall or the furniture it runs against, keep it smooth with no twists, and fasten the ends with a small cable tie so the sleeve cannot slide down and bunch up. It is the only fix in this post that works on a cable you can see from every angle — which is exactly why it is worth the $7.
10. Hide the router and its cables in a decorative basket
The router is the worst offender in a small home: it needs power, a phone line and a cable to the TV, and it usually sits in the middle of everything, blinking. A lidded basket — wicker, seagrass or fabric, about 30 cm across — hides the router, its cables and the power strip in one move, and it looks like storage, not a cover-up. Cut a small hole in the back of the basket for the cables, stand the router upright inside it with the aerials poking through the weave, and put the lid on loosely so the heat can escape. A basket costs about $8 second-hand and doubles as a home for the spare chargers and the coiled cables from idea 2. Two warnings: never use a metal box — it blocks the Wi-Fi signal — and never close the lid tight on a running router, because a hot router in a sealed box will slow down and can fail early. If the Wi-Fi feels slower after the move, lift the lid or cut a bigger vent hole.
Fix the Desk and TV Corner
Two spots produce most of the cable mess in a small home: the desk, where a laptop, a monitor, a lamp and a phone all charge at once, and the TV corner, where the console, the soundbar and the streaming stick all want a socket. Fix those two corners and the whole home looks tidy.
11. Screw an under-desk cable tray to the desk
An under-desk cable tray is a shallow metal basket that fixes under the desktop and holds the power strip and all the slack cable off the floor and out of sight. A tray costs about $10, screws on with four short screws, and takes fifteen minutes to fit — measure twice, because the screws must be shorter than the desktop is thick. Once it is up, the power strip lives in the tray, the cables drop from the laptop straight into it, and the only thing visible under the desk is a single cord running to the wall. If you rent and cannot screw into the desk, use the adhesive version instead: it sticks on with heavy-duty tape and holds a light strip and a few cables, though it will not carry a full power strip. Either way, the rule is the same — nothing on the floor under the desk, because floor cables under a desk are the first thing to get kicked, tangled and broken.
12. Hide the TV cables in one vertical raceway behind the screen
The TV corner has the most cables and the simplest fix: one vertical cord cover running straight down from the back of the TV to the socket, painted the colour of the wall. Measure the drop — usually 60 to 90 cm from a wall-mounted TV to the socket — and buy a raceway that long, or two shorter lengths joined with a connector. Stick it dead centre behind the TV so the screen hides the top of it, thread the power cable, the HDMI cable and the aerial cable inside, and snap the lid on. If the TV sits on a stand instead of the wall, run the same cover down the back of the stand and let the stand hide the bottom. The finishing touch is a cable box at the socket end: the strip, the console and the soundbar all plug into one hidden box, and from the sofa the whole wall looks like just a TV. Our guide to organizing a small home office in a corner uses the same tray-and-cover system at the desk — and for the wider renter-friendly rule behind every fix here, our 20 renter-friendly DIY upgrades that need no drilling covers the no-drilling, no-damage approach in full. Browse every decor idea on the DIY Decor category page.
A Worked Example: Hiding Every Cord in a Small Living Room for $29
Here is the starter kit for a typical small living room with a TV, a router and a lamp, and what each piece does:
| Item | Cost | What it does |
|---|---|---|
| Cord cover, 1 metre, paintable | $8 | Hides the whole TV cable run down the wall |
| Cable management box | $12 | Swallows the power strip and six plugs behind the TV |
| Velcro cable ties, pack of 20 | $3 | Bundles the loose cables into one neat cord |
| Adhesive cable clips, pack of 6 | $4 | Keeps phone and laptop chargers on the desk edge |
| Masking tape labels | $2 | Labels both ends of every cable so nothing is unplugged by mistake |
| Total | $29 | One afternoon to fit, every cord hidden |
That $29 total is the starter kit only — it assumes you already own a paintbrush and a spare basket for the router. Add $10 for an under-desk tray if the desk is the worst spot, and $7 for a fabric sleeve if one cable has to stay visible. The fitting order matters: trace and label on the first pass, unplug the dead cables, then fit the cord cover, then the cable box, then the clips — the cover and the box do the heavy lifting, and the clips are the finishing touch. The result is not just tidier: cables that are bundled, boxed and off the floor last longer, collect less dust, and stop being tripped over — which is the real saving, because a replaced laptop charger costs more than this whole kit.
Your Cord-Hiding Checklist
Work through this list in order — trace, then unplug, then cover, then box — and tick each step off as you finish it:
- Trace every cord at the TV and the desk and label both ends with masking tape
- Unplug the dead cables and coil them in one labelled box in a cupboard
- Measure the TV cable run and buy a cord cover long enough to reach the socket
- Stick the cord cover tight along the skirting board and paint it the wall colour
- Push furniture closer to the wall so the gap behind it swallows the cable runs
- Tape flat any cable that must cross open floor, or run it under a rug
- Drop the power strip into a cable box with the lid loose for airflow
- Bundle the cables that run together with velcro ties every 30 cm
- Stick a cable clip on the desk edge for each charger you use daily
- Hide the router in a ventilated basket with the aerials poking through the weave
- Fit an under-desk tray and get every cable off the floor under the desk
- Run one vertical raceway behind the TV and put a cable box at the socket end
Where Should You Start?
Start with the masking tape and ten minutes of tracing. Labelling both ends of every cord costs nothing, and it usually shrinks the tangle by a third before you buy anything — the dead cables go in a bag, the live ones get a name, and suddenly the job looks small.
Then buy the cord cover and the cable box first, because those two pieces do most of the work for $20. Fit the cover down the wall behind the TV, drop the power strip in the box, and the room changes in an afternoon — the rest is finishing touches. If the desk is your worst spot, our corner home office guide shows the same system at a desk, and you can browse every decor idea on the DIY Decor category page.
Frequently Asked Questions
Is it safe to hide power strips inside a cable box?
Yes, as long as the box is ventilated and the lid is left loose. Cable boxes are made with slots in the sides for cables and airflow, and that airflow is what keeps the strip cool. Never use a sealed box, never stack two strips in one box, and check the strip once a month for warmth — if it feels hot to the touch, take it out of the box and spread the plugs across two sockets instead.
Can I hide cables in a rental without losing my deposit?
Yes — every fix in this post is renter-friendly. Cord covers stick on with adhesive tape and peel off cleanly, cable boxes sit on the floor, velcro ties wrap on and off, and adhesive clips pull away without marking the paint. Nothing is screwed, drilled or glued permanently, so you can take the whole system down when you move out — just keep the paint you used on the cord cover, so you can touch up the wall if a strip leaves a mark.
What is the cheapest way to hide TV cables?
Push the TV stand closer to the wall and drop the cables behind it — free, and it hides most of the run. If the TV is wall-mounted, a single paintable cord cover costs about $8 and hides the whole vertical drop in ten minutes. A cable box at the socket end, about $12, finishes the job by swallowing the power strip and all the plugs, so from the sofa you see only the TV.
How do I stop phone chargers falling behind the desk?
Stick an adhesive cable clip to the edge of the desk or bedside table and thread the charger through it, leaving about 15 cm of cable hanging past the clip. The clip holds the end exactly where your hand expects it, and the cable can never slide off the edge again. A pack of six clips costs about $4, they peel off cleanly when you move, and the same trick works on a bedside table where chargers usually fall behind the bed.

Comments (0)
Post a Comment