Simple DIY, organization & cleaning tips for every home — new guides every week

How to Unclog a Drain and Fix a Leaky Faucet Without a Plumber

 

How to unclog a drain and fix a leaky faucet — clean bathroom sink with plunger, adjustable wrench and folded towels in sage green and terracotta tones

A slow drain and a dripping faucet are the two small plumbing jobs most people put off for months. The drain takes longer and longer to empty, the faucet taps all night, and the water bill creeps up — yet both jobs look harder than they are, so the call to a plumber keeps getting postponed.

Learning to unclog a drain and fix a leaky faucet yourself changes that. Most slow drains clear with a plunger in about 10 minutes, and most dripping faucets stop with a new washer or cartridge that costs under $10. This guide takes you through both jobs in order, with the exact tools, timings and safety checks, so you can finish in one Saturday morning.

Quick Answer

Start with the plunger: seal it over the drain, plunge 15–20 times, then flush with hot water. If that fails, clean the trap or use a 5-metre drain snake. For a dripping faucet, turn off the water, replace the worn washer or cartridge, and reassemble. Most slow drains and drips take under an hour and cost less than $20.

Key Takeaways

  • A plunger clears most slow drains in about 10 minutes — try it before any chemical cleaner.
  • Always turn off the water supply and put a bucket under the trap before opening any pipe or faucet.
  • A dripping faucet is usually one worn washer or cartridge, a part that costs under $10.
  • Never pour chemical drain cleaner into a drain you may need to open by hand.
  • If water is leaking inside a wall, the main shut-off will not hold, or the drain backs up in several rooms at once, stop and call a plumber.

Before You Start: Two Safety Checks First

Plumbing jobs go wrong in two predictable ways: water goes where it should not, and a chemical meant for the drain ends up on someone's hands. Two checks before you touch anything prevent both.

1. Find the water shut-off before you need it

For a faucet, the shut-off valves are usually under the sink — two small oval or lever handles on the hot and cold pipes. Turn both clockwise until they stop, then open the faucet to check the water has actually stopped; if a stiff valve will not turn, use the main house shut-off instead and do not force it until it breaks. For a drain, you do not need to shut off the supply, but put a bucket under the trap and towels on the floor, because the trap always holds water even when the sink is empty.

2. Skip chemical drain cleaners entirely

Chemical drain cleaners rarely clear a real blockage, they can damage older pipes and seals, and they leave caustic liquid sitting in the trap — which then splashes out when you open it. If a bottle is already in the drain, wear rubber gloves and eye protection, plunge gently, and flush well with water first.

Tools and Parts You Actually Need

Both jobs share most of the same kit, so gather everything once and do the drain first, then the faucet, in a single session.

ItemWhat it is forTypical cost
Cup plunger (sink size, not toilet size)Clearing slow sink and bath drains$5–$10
Drain snake, 5 metresBlockages past the trap$10–$15
Adjustable wrenchTrap nuts and faucet fittings$8–$12
Rubber gloves and old towelsTrap water and dripsAlready at home
Bucket, at least 10 litresCatching trap waterAlready at home
Replacement washer set or faucet cartridgeStopping the drip$3–$10
Plumber's tape (PTFE tape)Sealing threaded joints$2–$3
Old toothbrush and white vinegarCleaning the trap and aerator$2–$3

Total for a first session: about $15 to $25 if you already own a wrench, or $30 to $45 buying the plunger, snake and wrench together. Take a photo of your faucet brand and model, and of the old washer or cartridge, before you go shopping — faucet parts are not universal, and the photo saves a second trip.

Unclog a Slow Drain Step by Step

Work in this order, and stop as soon as the water drains freely. Most drains clear at step 3 — do not open the trap unless the plunger has genuinely failed.

3. Plunge it properly: seal, then 15–20 firm strokes

Remove the sink stopper and any drain cover, and block the overflow hole with a wet cloth — without that seal, the pressure escapes through the overflow instead of pushing the blockage. Run enough water to cover the plunger cup by about 2 cm, press the cup down to seal it over the drain, then plunge up and down firmly 15 to 20 times without lifting the cup. Lift, let the water drain, and repeat twice if it is improving. If the water suddenly drains fast, run the hot tap for 2 minutes to flush the loosened debris away.

4. Clear the stopper and the first bend by hand

If plunging barely helps, the blockage is often hair and soap scum wrapped around the stopper itself. Pull the stopper out, clean it with an old toothbrush, and reach into the first few centimetres of the drain with a gloved hand or a small plastic drain stick — you will often pull out a clump of hair in under a minute. Rinse the stopper in hot water, refit it, and test the drain again before going further.

5. Open and clean the trap (the U-bend under the sink)

Put the bucket under the trap, unscrew the two slip nuts by hand or with the wrench, and let the trapped water drain into the bucket. Tip the trap out, scrub it with the toothbrush and hot soapy water, and check the short pipe into the wall for a visible blockage. Refit the trap, hand-tighten the nuts, then give each a quarter-turn with the wrench — overtightening cracks plastic traps. Run the tap for a minute and check both joints with a dry fingertip; a drip means a nut needs a small extra turn. For ideas on keeping the space under the sink tidy, see our guide to small bathroom storage ideas that double your space.

6. Use the drain snake for blockages further down

Feed the snake slowly into the drain, turning the handle clockwise as you push, until you feel resistance — usually 1 to 3 metres in for a bathroom sink. Crank gently to break up or hook the blockage, then pull the snake back slowly, wiping debris off with a cloth as it emerges. Never force the snake: if it will not pass a bend, pull back and try again at a slightly different angle. Flush with hot water for 2 minutes afterwards, and wash the snake before storing it, so it does not rust or smell.

Fix a Leaky Faucet Step by Step

A faucet that drips once every few seconds can waste more than 10 litres a day. The steps below fit most standard two-handle and single-lever faucets; if your faucet has no visible screws, look for a small cap or grub screw under the handle first, and do not pry the handle off.

7. Turn off the water and drain the faucet

Close both under-sink shut-off valves, then open the faucet to let the remaining water out and confirm the flow has stopped. Plug the sink drain with a cloth or stopper — small screws and washers love to fall down an open drain, and fishing one out doubles the job time. Lay the parts out in the order you remove them, left to right, so reassembly is simply the reverse.

8. Remove the handle and find the worn part

Undo the handle screw, lift the handle off, and unscrew the bonnet nut or cartridge retaining nut with the adjustable wrench. Pull out the cartridge or the stem, and look at the washer at its base: a washer that is flattened, cracked, split or grooved is the drip. In a cartridge faucet there is no separate washer — the whole cartridge is the part, and it lifts out as one unit. Take the old part to the shop, or match it from your photo, and buy the exact replacement.

9. Fit the new washer or cartridge and reassemble

Fit the new washer or cartridge the same way round as the old one — cartridges usually have a notch or flat side that only fits one way, so do not force it. Wrap plumber's tape clockwise around any threaded joint, about 4 to 5 turns, pulling it tight so it sits flat. Refit the bonnet nut firmly but not brutally tight, replace the handle and its screw, and remove the drain plug. Turn the water back on slowly, starting with the cold valve, and watch the faucet and the under-sink joints for 2 minutes before calling the job done.

10. If it still drips, check the seat and the aerator

A new washer that still drips usually means the valve seat — the surface the washer presses against — is rough or pitted. If it feels rough, a cheap seat-dressing tool can smooth it, or a plumber can reseat it in minutes. While you are there, unscrew the aerator at the faucet tip, soak it in vinegar for 10 minutes, and refit it — a clogged aerator causes spluttering that looks like a faucet problem but is not.

A Saturday Morning Plan: Both Jobs in About an Hour

Do the jobs in this order, and the whole session fits into one morning with a coffee break in the middle.

TimeJobWhat you should see
0:00–0:10Plunge the drain (step 3)Water drains fast, or clearly faster than before
0:10–0:20Clean stopper, or open trap if needed (steps 4–5)Trap clean, joints dry after a 1-minute run
0:20–0:25Coffee break while the drain flushesNo drips under the sink
0:25–0:40Faucet: shut off, strip, replace washer (steps 7–9)New part fitted the right way round
0:40–0:50Turn water on, check, clean aerator (steps 9–10)No drip after 2 minutes, steady flow
TotalAbout 50 minutes active workOne fast drain, one silent faucet, under $25 spent

Stop It Happening Again: A 5-Minute Monthly Checklist

Run through this checklist once a month — it takes about 5 minutes and prevents most repeat blockages and drips.

  • ☐ Drain strainer in place, emptied of hair and food bits after every use
  • ☐ Hot water run for 1 minute after greasy washing-up, so grease does not set in the trap
  • ☐ Faucet handles close without forcing — a handle that needs a hard twist is wearing its washer
  • ☐ Under-sink joints checked with a dry fingertip — damp means a nut needs a quarter-turn
  • ☐ Aerator rinsed every 3 months, or sooner if the flow starts to splutter
  • ☐ Nothing but water, soap and toothpaste goes down the bathroom drain — no cotton pads, wipes or dental floss

When to Stop and Call a Plumber

Knowing when to stop is part of the skill. Call a plumber if water is leaking inside a wall or ceiling, if the main shut-off will not hold, if several drains back up at the same time (a main-line blockage, not one sink), or if a fitting is seized and risks breaking the pipe. The same applies to any corroded or soft pipe. A call-out here is far cheaper than a burst pipe and a flooded floor.

Where Should You Start?

Start with the drain, because it gives the fastest win: plunge it this evening, following step 3 exactly, and you will know within 10 minutes whether you need to go further. If the plunger works, flush with hot water and tick the monthly checklist above — you are done.

Tomorrow, fix the faucet: buy the washer or cartridge first, using the photo of the old part, then work through steps 7 to 9 in one calm session. Once both jobs are done, you will have spent under $25 and saved a plumber's call-out fee — and the next drip or slow drain will feel like a 10-minute job, not a problem. Browse our Home Fixes category for more small repairs in this series.

Once the drain and tap are sorted, the next water-wasting fix is a running toilet: our guide to how to fix a running toilet and save water shows you how to stop a leak that can waste up to 750 litres a day in about 30 minutes.

Once the tap is sorted, the next leak to fix is the showerhead: our guide to how to fix a leaky showerhead and save water uses the same washer-and-tape skills to stop a drip that can waste about 11,000 litres a year in 15 minutes.

Frequently Asked Questions

Can I use a plunger on a bathroom sink drain?

Yes, use a small cup plunger, not a toilet flange plunger. Block the overflow hole with a wet cloth, cover the cup with about 2 cm of water, and plunge 15 to 20 times without lifting the cup. If the drain is still slow after three rounds, move on to cleaning the stopper or the trap rather than plunging harder.

Why does my faucet still drip after I replaced the washer?

The usual cause is a rough or pitted valve seat that the new washer cannot seal against. Check the seat with a fingertip: if it feels rough, it needs smoothing with a seat-dressing tool or a plumber's visit. Also check the new washer is the exact size and fitted the right way round — a washer that is slightly too small will drip from day one.

Is it safe to use a drain snake myself?

Yes, for a single sink or bath drain, if you feed it slowly and never force it past resistance. Turn the handle clockwise as you push, pull back and retry if it sticks at a bend, and stop if you meet solid resistance that will not move — that may be a pipe joint, not a blockage. Do not use a powered snake on a home drain unless you have been shown how; a hand snake is enough for most household blockages.

How much does a plumber charge for a slow drain or a dripping faucet?

Prices vary by area, but a simple drain clear or washer replacement is typically a minimum call-out of $75 to $150, while the parts for doing it yourself cost under $10 for a washer set and $10 to $15 for a hand drain snake. That is why both jobs are worth learning: one DIY session usually pays for all the tools you buy for it.

About the Author

Small Home Hacks shares simple, tested DIY ideas, organization systems and cleaning routines that make everyday living easier — no big budget or big house needed.

Comments (0)

Post a Comment

Search This Blog

Powered by Blogger.

Ads

Ads

Ads