Simple DIY, organization & cleaning tips for every home — new guides every week

How to Stop Condensation on Windows in Winter

Condensation droplets on a cold windowpane in winter with a small green plant on the windowsill, bright sage green room, soft morning light, no people, no text

You wake up on a cold morning, and every window in the house is wet. Water runs down the glass, pools on the sill, and by February there are black spots creeping along the frame. It looks like a window problem, and most people try to fix it at the window — new seals, thicker curtains, a towel on the sill. None of that works for long, because the window is not the problem. The window is only where the problem shows up.

Condensation on windows happens when warm, moist air inside your home meets cold glass: the air cools, it can no longer hold its water, and the water lands on the pane. A family of four puts roughly 10 litres of moisture into the air every day just by breathing, cooking, showering and washing. Fix the moisture in the air, and the windows dry themselves. Here are 12 ideas, starting with the one measurement that tells you everything, then the daily routine that costs nothing, then the cheap fixes that warm the glass.

Quick Answer: Condensation forms when warm, moist indoor air hits cold window glass. Keep indoor humidity between 30% and 40% in winter: ventilate for 10 minutes twice a day, run the extractor fan during showers and cooking, and dry laundry outside or in a vented room. A $12 window insulation film kit warms the glass enough to stop most drips overnight.

Key Takeaways

  • Condensation is a humidity problem, not a window problem: warm moist air cools on cold glass and leaves its water behind.
  • Aim for 30–40% indoor humidity in winter, measured with a $8 hygrometer — below 30% dries out skin and wood, above 40% wets the glass.
  • Ventilate for 10 minutes twice a day, and run the extractor fan every time you shower or boil water.
  • A load of laundry drying indoors releases about 2 litres of water into the air — dry it outside or in a vented room.
  • A $12 window insulation film kit and a 60-second morning squeegee stop most drips for under $25 in total.

Why Your Windows Get Wet

Condensation feels mysterious the first winter it happens, but the physics is simple, and once you see it, the fix is obvious. Two numbers decide whether your windows are wet or dry in the morning: the temperature of the glass, and the amount of water in the air.

1. Learn the dew point in 60 seconds

Warm air holds more water than cold air. When warm room air touches a cold windowpane, the air cools down fast — and the water it was carrying has to go somewhere, so it lands on the glass as droplets. The temperature at which that happens is called the dew point, and in a heated home in winter it is usually around 10–13°C. Single glazing sits close to the outside temperature, so it is almost always below the dew point on a cold night, which is why old windows stream with water while double-glazed ones only mist at the edges. You cannot change the physics, but you can change both sides of it: warm the glass a little, or dry the air a little, and the condensation stops. Every idea in this post does one of those two things.

2. Measure your humidity — aim for 30–40%

Guessing humidity is useless, because a room that feels dry can still be at 55% and wetting the windows every night. Buy a small digital hygrometer — they cost about $8, run on one button battery, and sit on a shelf showing temperature and humidity at a glance. Put it in the bedroom, which is usually the worst room because two people breathe out moisture there all night with the door shut. In winter, aim for 30–40% relative humidity: below 30%, your skin, throat and wooden furniture dry out; above 40%, the windows start to weep on cold mornings, and above 60%, mould has everything it needs. Check the reading morning and evening for a week, and write the two numbers down — that little log tells you whether your problem is a damp house or just one damp habit, like drying laundry in the bedroom.

Cut Moisture at the Source

A family of four adds about 10 litres of water to the air of a small home every day: roughly 3 litres from breathing overnight, 2 litres from showers, 2 litres from cooking, and the rest from washing and drying. You cannot stop breathing, but the other sources are all fixable, and cutting them is free.

3. Run the extractor fan every shower and every boil

A bathroom extractor fan pulls about 15 litres of steamy air per second out of the house — but only if it is actually running. Turn it on before you step into the shower, not after, and leave it running for 20 minutes afterwards: the steam is still in the air long after the mirror clears, and 20 minutes is what it takes to clear it. Do the same in the kitchen — the cooker hood or extractor goes on before the pot boils, not when the kitchen is already foggy, and it stays on until the steam stops. If your bathroom fan is the kind that runs on a timer after the light goes off, leave the light on for those 20 minutes so the timer finishes its job. This one habit removes more moisture from a small home than any gadget you can buy, and it costs nothing but remembering.

4. Put lids on pots and shorten steamy showers

A pot of water boiling uncovered releases a surprising amount of steam into the kitchen — a lid on the pot cuts it by more than half, and the food cooks faster too. Keep lids on whenever water is boiling or simmering, and use the back burners so the steam rises under the extractor hood instead of into the room. In the bathroom, a shower that runs 5 minutes instead of 15 puts roughly a third less water into the air, and a cooler shower steams less than a scalding one. These are small changes, but in a small home the bathroom and kitchen are a few steps from the bedrooms, and the steam does not stay where it was made — it drifts through the whole home and lands on the coldest glass it finds.

5. Stop drying laundry on radiators

One load of laundry drying indoors releases about 2 litres of water into the air — and drying it draped over a warm radiator releases it fast, right into the room where you sleep. If you have any outdoor space, dry laundry outside even in winter: cold air still dries clothes, it just takes longer, and the moisture goes into the sky instead of onto your windows. If you must dry indoors, use a clothes airer in the bathroom with the extractor fan running and the door shut, or in the room with the best ventilation, never in a closed bedroom. A tumble dryer that vents outside is the other answer, but it costs far more to run than the airer-and-fan method, which costs nothing at all.

Ventilate Every Day — Even in Winter

The advice sounds backwards — open the windows when it is freezing outside? — but it is the single most effective thing you can do. Cold winter air holds almost no moisture, so when it comes inside and warms up, it soaks up the damp air like a sponge. Ten minutes of fresh air replaces a surprising amount of wet indoor air with dry outdoor air.

6. Air the house for 10 minutes, twice a day

Open two windows on opposite sides of the home, or a window and a door, for 10 minutes in the morning and 10 minutes in the evening. Cross-ventilation matters: one open window barely moves the air, but two open on opposite sides create a draught that swaps the air in a small home almost completely in 10 minutes. Do the morning airing while you make breakfast, when the house is at its dampest after a night of breathing and showers. Yes, you lose some warm air — about the cost of heating the house for an extra 10 minutes — but you bring in dry air that will not wet the windows, and a dry home is cheaper to heat than a damp one, because damp air takes more energy to warm. If 10 minutes feels too cold, open the windows wide for 5 minutes instead of leaving one cracked all day: a short, wide airing swaps the air without cooling the walls, and cold walls are what the damp condenses on.

7. Open trickle vents and keep air moving

Most modern windows have a trickle vent — a narrow slot at the top of the frame that lets a little air in all day without opening the window. If yours are shut, open them and leave them open all winter: that slow, steady trickle is exactly what a small home needs, and it is designed to be left open. Keep bedroom doors open during the day, or at least ajar, so moist air does not get trapped in one cold room overnight. And do not push furniture hard against outside walls: a wardrobe or bed pressed tight to a cold wall traps damp air behind it, and that is where mould starts — leave a 5 cm gap so air can circulate, and the wall stays dry.

Warm the Glass and Insulate

The other side of the equation is the glass itself. If the inside surface of the window is warmer than the dew point, water cannot condense on it — no matter how humid the air is. You do not need new windows to get there; a few cheap layers do most of the job.

8. Fit window insulation film — $12, 20 minutes

A window insulation film kit costs about $12 and covers one large window or two small ones. You stick double-sided tape around the frame, press the clear plastic film onto the tape, and shrink it tight with a hair dryer — it goes drum-tight and almost invisible, and it adds a still layer of air between the room and the glass. That trapped air is the insulation: it warms the inside surface of the window by several degrees, often enough to lift it above the dew point on all but the coldest nights. Fit it in October or November, before the cold sets in, and peel it off in spring — it leaves no marks on the frame. For a bedroom window that streams every morning, this is the cheapest fix that actually works, and it takes about 20 minutes per window.

9. Close thermal curtains at dusk, open them at dawn

Heavy lined curtains, closed as soon as it gets dark, add a second insulating layer in front of the glass and keep the warm room air away from the cold pane. The trick is the timing: close them at dusk, when the glass starts to cool, and open them again in the morning so daylight and warm air reach the glass and any light mist dries off. Leaving curtains closed all day traps cold, damp air between the curtain and the window — which is exactly the mould factory you are trying to avoid. If new thermal curtains are not in the budget, a thick blanket or an old duvet hung over the window at night does the same job, and costs nothing. Whatever you hang, make sure it does not sit in the puddle on the sill: a curtain hem that soaks up condensation every night will go mouldy itself.

10. Draught-proof the frame, not the vent

Cold air leaking in around an old window frame makes the glass colder and the room draughtier, so seal the gaps — but seal the right ones. Self-adhesive foam draught-excluder tape costs about $6 a roll, sticks around the opening part of the frame in 10 minutes, and stops the cold draught that chills the glass. Do not seal the trickle vent, and do not block the gap under an internal door: those are the paths that let damp air out, and blocking them makes condensation worse, not better. If the seal around the glass itself is broken — you can tell because the inside of a double-glazed unit is misted and never clears — that unit has failed, and no tape will fix it; that is a job for a glazier, and it is the one fix in this post that is not a DIY job. For the monthly check that catches a failing seal before winter, see our monthly home maintenance checklist for beginners.

Deal With the Water That's Already There

Even with everything above, the coldest mornings of the year may still leave a little mist on the glass. What matters then is getting the water off the window quickly, before it soaks into the frame and feeds mould.

11. Squeegee the glass dry every morning

Keep a small window squeegee — about $5 — on the bedroom windowsill, and spend 60 seconds each morning pulling the water off the glass and into a cloth. A window vacuum does the same job faster and sucks the water into a tank instead of dripping it down the wall, but it costs $25–$40, so start with the squeegee. Wipe the sill dry with a microfibre cloth after, and leave the cloth to dry on the radiator, not bunched up wet on the sill. Sixty seconds a day is the difference between a window that dries out by mid-morning and a frame that stays wet all winter — and wet wood rots, paint peels, and mould moves in. Make it part of the morning routine, like making the bed, and it stops feeling like a chore.

12. Treat black mould spots before they spread

If black spots have already appeared around the window frame, deal with them now, while they are small. Wearing gloves, wipe the spots with a cloth dampened with white vinegar or a diluted bleach solution (one part bleach to ten parts water), then rinse with clean water and dry the area completely. Never dry-brush or vacuum mould — that throws spores into the air. Once the spot is clean and dry, keep the window dry with the morning squeegee, and the mould has nothing to grow on. If the mould keeps coming back in the same place even after the window stays dry, the wall itself may be damp from outside — a leaking gutter or cracked render — and that is a job for a professional, not a cleaning product. And if mould is a recurring worry in your home, the ventilation routine in this post is the fix that stops it at the source.

A Worked Example: A Dry-Window Winter Morning for $25

Here is the starter kit that stops most condensation in a small home, and what each piece does:

ItemCostWhat it does
Digital hygrometer$8Tells you the real humidity, so you know when to act
Window insulation film kit (1 window)$12Warms the glass above the dew point
Window squeegee$5Clears morning water off the glass in 60 seconds
Microfibre cloths (pack of 3)$0–$3Dries the sill without leaving lint
Draught-excluder tape (1 roll)$6Seals the frame gaps that chill the glass
Total$25–$31About 40 minutes to fit everything

That $25 assumes you already have cloths at home and buy one film kit for the worst window — add $12 per extra window, and $30 if you upgrade the squeegee to a window vacuum later. The daily routine itself is free: 10 minutes of airing twice a day, the extractor fan on every shower, and a 60-second squeegee each morning. Total time: about 25 minutes a day, most of it just leaving windows open while you get on with breakfast.

Your Condensation Checklist

Work through this list in order — measure first, then cut the moisture, then warm the glass — and tick each step off as you finish it:

  • ☐ Buy a hygrometer and put it in the bedroom — check the reading morning and evening for a week
  • ☐ Aim for 30–40% humidity in winter; above 40%, start ventilating more
  • ☐ Run the extractor fan before every shower and leave it on for 20 minutes after
  • ☐ Run the cooker hood before the pot boils, and keep lids on boiling pots
  • ☐ Move laundry drying out of the bedroom — outside, or in the bathroom with the fan on
  • ☐ Open two windows on opposite sides for 10 minutes, morning and evening
  • ☐ Open the trickle vents on every window and leave them open all winter
  • ☐ Fit window insulation film on the worst window — $12, 20 minutes, hair dryer to shrink it
  • ☐ Close thermal curtains at dusk, open them at dawn so the glass can dry
  • ☐ Seal frame gaps with draught-excluder tape — but never block the trickle vent
  • ☐ Squeegee the glass and wipe the sill dry every morning, 60 seconds
  • ☐ Wipe any black mould spots with vinegar or diluted bleach, gloves on, and keep the area dry

Where Should You Start?

Start with the hygrometer. Spend $8, put it in the bedroom, and read it morning and evening for three days. That one number tells you whether you have a damp-house problem or a damp-habit problem — and it stops you buying things you do not need.

Then do the free things for a week: air the house for 10 minutes twice a day, run the extractor fan on every shower, and keep the laundry out of the bedroom. Most small homes see the morning condensation halve in the first week on those three habits alone. If the worst window still streams after that week, fit the $12 insulation film — it is the cheapest fix that warms the glass itself, and it is the step that finishes the job. Once the windows stay dry, the next step is keeping the warmth in: our guide to keeping a small home warm in winter without high bills shows how to seal the drafts and heat only the room you are in for about $36. Browse all our easy home fixes on the Home Fixes category page.

Frequently Asked Questions

Why do my windows get condensation in winter but not summer?

In summer the glass is warm, so it stays above the dew point and water stays in the air instead of landing on the pane. In winter the glass is cold — often below the 10–13°C dew point of a heated home — so the same moist air leaves its water on the window. Single-glazed windows are worst because the glass sits close to the outside temperature, but even double glazing mists at the edges on the coldest nights.

What humidity level stops condensation on windows?

Aim for 30–40% relative humidity indoors in winter. Below 30% dries out skin, throats and wooden furniture; above 40% the windows start to weep on cold mornings, and above 60% mould has everything it needs to grow. Measure with a digital hygrometer in the bedroom — guessing does not work, because a room that feels dry can still read 55%.

Will opening a window in winter make condensation worse?

No — it makes it better. Cold winter air holds almost no moisture, so when it comes inside and warms up, it soaks up the damp indoor air. Open two windows on opposite sides for 10 minutes twice a day for proper cross-ventilation. A short, wide airing swaps the air without cooling the walls, which is better than leaving one window cracked all day.

Is condensation on windows a sign of a serious problem?

Usually not — in most small homes it is just warm, moist air meeting cold glass, and the routine in this post fixes it. But if one window stays misted inside a double-glazed unit and never clears, its seal has failed and the unit needs replacing. And if mould keeps returning in the same spot even after the window stays dry, the wall may be damp from outside — a leaking gutter or cracked render — which needs a professional, not a cleaning product.

About the Author

Small Home Hacks shares simple, tested DIY ideas, organization systems and cleaning routines that make everyday living easier — no big budget or big house needed.

Comments (0)

Post a Comment

Search This Blog

Powered by Blogger.

Blog Archive

Ads

Ads

Ads