A leaky showerhead is the kind of problem you hear before you see: a steady drip, drip, drip in the bathroom long after the shower is off, or a thin line of water running down the shower arm and onto the tiles. It looks harmless — it is only a few drops, after all — but a showerhead dripping once a second wastes around 11,000 litres of water a year, and in a small home that water is quietly running down the drain and onto your water bill.
How to fix a leaky showerhead comes down to three steps: find exactly where the water is escaping, replace the worn washer or re-tape the thread, and clean out any limescale that is forcing water sideways. Most leaks are fixed in 15 minutes with a washer that costs about $1 and a roll of plumber's tape, and you do not need to call a plumber or turn off the water to the whole house.
Quick Answer: Most leaky showerheads are fixed in 15 minutes by unscrewing the head, replacing the small rubber washer inside the connection and wrapping the shower arm thread with 5 to 6 turns of plumber's tape. A showerhead dripping once a second wastes about 11,000 litres of water a year, and the repair costs about $3 in parts.
Key Takeaways
- A drip from the showerhead face means a worn washer or a clogged head, while a drip from the connection means the thread seal has failed.
- The washer inside the showerhead connection costs about $1 and takes two minutes to replace.
- Wrap the shower arm thread with 5 to 6 turns of plumber's tape, clockwise, or the tape unwinds when you screw the head back on.
- Soaking the head in white vinegar overnight dissolves the limescale that blocks nozzles and forces water sideways.
- A showerhead dripping once a second wastes about 11,000 litres a year, so a $3 fix pays for itself in weeks.
Table of Contents
Find the Leak First: Diagnose Before You Fix
Every showerhead leak has a cause, and the fix depends on which one it is. Spend five minutes diagnosing before you buy anything, because a washer fixes one kind of leak and does nothing for another. Dry the showerhead and the arm with a towel, then watch for a full minute while the shower is off.
1. Watch where the water comes from
There are only two places a showerhead can leak: the face of the head, where the water sprays out, or the connection, where the head screws onto the shower arm. Dry both spots, then wait. If drops form on the face and fall from the nozzles, the water is getting past the washer or the head is clogged and holding water. If water beads at the joint and runs down the arm, the thread seal has failed. Note which one it is — that tells you whether to reach for a washer or for plumber's tape. A leak at the wall end of the shower arm is a different job: that joint is behind the wall plate, and if it drips there, tighten the arm by hand first and read idea 11 before going further.
2. Check the washer before you buy parts
Unscrew the showerhead by hand — it should turn counter-clockwise with a firm grip, and if it will not move, wrap a cloth around it and use pliers gently so you do not scratch the chrome. Look inside the end of the head: there is a small rubber ring, the washer, sitting in a groove. If it is flat, cracked, hard or squashed out of shape, it has failed, and no amount of tightening will seal the joint. Take the old washer with you to the shop — washers come in several sizes, and matching the old one by eye is the only reliable way to get the right size. A pack of assorted washers costs about $2 and covers every showerhead you are ever likely to own.
3. Test the water pressure
High water pressure makes showerheads leak even when the washer is fine. If your shower sprays hard enough to sting and the head drips for minutes after you turn it off, the pressure is probably above 5 bar, and the head is being forced open by the water behind it. You can test it with a pressure gauge screwed onto an outdoor tap, or ask your water supplier what the pressure in your street is. If it is above 5 bar, a pressure-reducing valve on the main supply fixes not only the showerhead but every dripping tap in the house — a plumber fits one in about an hour. This is the only step in this post that needs a professional, and it is worth doing, because pressure that is too high wears out every washer and valve in the home.
Fix the Connection: The 15-Minute Repair
Nine out of ten showerhead leaks are fixed at the connection, and the whole repair takes about 15 minutes with two parts that cost a few dollars. Work with the shower off, keep a towel under the joint to catch the water left in the head, and take the old washer with you if you are buying a new one.
4. Tighten the head by hand, then a quarter-turn more
Before you replace anything, try the simplest fix: tighten the showerhead by hand, firmly, then give it one more quarter-turn with pliers wrapped in a cloth. Many leaks are nothing more than a head that has worked loose over months of being adjusted. Do not over-tighten — a quarter-turn past hand-tight is enough, and forcing it further can crack the plastic thread inside the head or strip the thread on the arm. If the drip stops, you are done. If it slows but continues, move on to the washer: tightening alone only works when the washer is still in good shape.
5. Replace the washer or O-ring
With the head unscrewed, pull the old washer out of its groove with a fingernail or the tip of a knife — it should lift out easily. Push the new washer into the same groove, flat side down, and press it in evenly all the way around so it sits level. Some showerheads use a thin O-ring instead of a flat washer; the job is the same, just roll the new ring into the groove until it sits flat. Screw the head back on by hand until it is snug, then the quarter-turn with pliers. Turn the shower on for 30 seconds, then off, and watch the joint for a full minute. A new washer seals instantly — if it still drips from the connection after a washer change, the problem is the thread, and that is the next step.
6. Wrap the thread with plumber's tape
Plumber's tape, also called Teflon tape or PTFE tape, is a thin white tape that seals the thread between the shower arm and the head. Clean the arm's thread with a dry cloth, then wrap the tape around it 5 to 6 times, pulling it tight so it moulds into the thread. The direction matters: wrap it clockwise as you look at the end of the arm, so that screwing the head on tightens the tape instead of unwinding it. Tear the tape off, smooth the end down with your thumb, and screw the head back on. A roll of tape costs about $2 and lasts for dozens of repairs, and this one step fixes almost every connection leak that a new washer alone could not. Our leaky faucet fix uses the same washer-and-tape method on taps, so if you have done one, you have done the other.
Clean and Descale: When the Leak Is Inside the Head
Sometimes the connection is perfect and the head still drips. That usually means limescale has built up inside the head, blocking some nozzles and forcing water out sideways, or the head is holding water after you turn the shower off. The fix is cleaning, not parts, and it costs almost nothing.
7. Soak the head in white vinegar overnight
Unscrew the head and put it in a bowl or a plastic bag filled with undiluted white vinegar, making sure the face of the head is fully covered. Leave it for 8 to 12 hours — overnight is ideal. The vinegar dissolves the limescale that builds up in hard-water areas, and you will see small white flakes in the bowl in the morning. Rinse the head under running water, then poke each nozzle with a pin or a toothpick to clear anything the vinegar loosened. Screw it back on, run the shower for a minute, and the spray should be even again. Do this every 6 months in a hard-water home and the head will last years longer. A litre of white vinegar costs about $3, and one bottle covers several cleanings.
8. Clear clogged nozzles with a pin
If only a few nozzles spray sideways or not at all, the problem is a single blocked hole, not the whole head. With the shower off, push a pin or a needle gently into each blocked nozzle and wiggle it once — you are clearing a grain of limescale, not drilling a new hole, so do not force it. Then run the shower for 30 seconds to flush the loosened scale out. Some modern showerheads have soft rubber nozzles: rub them with your thumb while the water is running and the scale pops off by itself, no pin needed. Check the nozzles once a month and a five-minute clean keeps the spray even and stops the sideways jets that soak the bathroom wall.
9. Replace the head if it is cracked or worn out
A showerhead does not last forever. If the plastic body is cracked, the thread inside the head is stripped so it will not tighten, or the face is so scaled that half the nozzles stay blocked after a vinegar soak, it is time for a new one. A basic replacement head costs $10 to $15, and fitting it is the same job as step 6: tape the thread, screw it on, quarter-turn. When you buy, check the flow rate on the box: a head rated at 1.5 to 2.0 gallons per minute (6 to 8 litres per minute) uses about a third less water than the old 2.5-gallon standard, and you will not notice the difference in the shower. Keep the old washer from the new head's box — it is a free spare for the next repair.
Stop the Drip for Good: Save Water and Money
Fixing the leak is half the job. The other half is making sure it does not come back, and turning the repair into a real saving on the water bill. A fixed showerhead is the cheapest water-saving upgrade in the house, because the water it saves was already paid for and going straight down the drain.
10. Fit a water-saving showerhead and measure the difference
A standard showerhead uses about 9 to 10 litres of water a minute; a water-saving head uses 6 to 8 litres and feels the same because it mixes air into the spray. For a 10-minute shower, that is 20 to 40 litres saved every single day — 7,000 to 14,000 litres a year for one person. Time your shower with a bucket test if you want the real number: hold a 10-litre bucket under the head and time how long it takes to fill. If it fills in under a minute, your head is using more than 10 litres a minute and a water-saving replacement will pay for itself in a few months. A good water-saving head costs $12 to $20 and screws on in two minutes.
11. Check the shower arm and the wall connection
The shower arm — the bent pipe the head screws onto — can work loose where it meets the wall, and that leak runs inside the wall where you cannot see it. Once a year, grip the arm firmly and check it does not wobble; if it moves, unscrew the wall plate and tighten the arm by hand, then a quarter-turn with pliers. Look for water stains or peeling paint on the wall below the arm, which are the signs of a hidden leak. If the arm itself is corroded or the thread is damaged, replace it: a new arm costs about $8, unscrews from the wall fitting, and the new one screws in with plumber's tape on the thread, just like the head. Never ignore a wall leak — water inside a wall causes damp and mould long before it shows on the surface.
12. Know when to call a plumber
Three situations are beyond a do-it-yourself fix. First, if the shower drips from the mixer tap or the wall valve, not from the head — that is a worn cartridge inside the tap, and replacing it means turning off the water supply and opening the valve body. Second, if the leak is inside the wall, with damp patches or a stain growing on the ceiling below the bathroom. Third, if the water pressure is above 5 bar and you need a pressure-reducing valve fitted. A plumber's visit for a cartridge change or a pressure valve costs $50 to $100, and it is money well spent: a hidden leak that runs for months costs far more in water and damp damage than the call-out fee. Everything else in this post — washer, tape, vinegar, new head — is a safe 15-minute job for anyone.
What Fixing a Leaky Showerhead Costs
Here is what the whole repair costs if you buy everything new, using the cheapest sensible option for each item:
| Item | Cost |
|---|---|
| Rubber washer, pack of assorted sizes | $2 |
| Plumber's tape (PTFE/Teflon), one roll | $2 |
| White vinegar, 1 litre | $3 |
| Pin or needle for clearing nozzles | $0 |
| Total, washer + tape + vinegar | $7 |
| Total, if you only need a washer | $2 |
| Total, with a new water-saving head | $19–$27 |
The honest version: most leaks are fixed for $2 — a washer and a roll of tape you probably already own. The vinegar is the only item with a real cost if your water is hard, and even then one bottle lasts for several cleanings. The real saving is not the repair cost but the water: a showerhead dripping once a second wastes about 11,000 litres a year, so a $2 washer pays for itself the first week. Our running toilet fix saves water the same way — a $5 flapper stops a leak that wastes even more than a dripping showerhead.
Your Leaky Showerhead Fix Checklist
Work through this list in order and tick each step off as you finish it:
- ☐ Dry the head and arm, then watch for a minute to find where the drip comes from
- ☐ Unscrew the head by hand and check the washer for cracks or flattening
- ☐ Replace the washer, flat side down, pressed evenly into its groove
- ☐ Wrap the shower arm thread with 5 to 6 turns of plumber's tape, clockwise
- ☐ Screw the head back on hand-tight, then one quarter-turn with pliers
- ☐ Turn the shower on for 30 seconds, then off, and watch the joint for a minute
- ☐ If the head still drips from the face, soak it in white vinegar overnight
- ☐ Clear blocked nozzles with a pin and flush the head for 30 seconds
- ☐ Check the shower arm for wobble and look for stains on the wall below it
- ☐ Do the bucket test: if a 10-litre bucket fills in under a minute, fit a water-saving head
- ☐ If the leak is from the mixer tap or inside the wall, call a plumber
- ☐ Put the spare washer and the tape roll in a labelled bag under the sink for next time
Where Should You Start?
Start with the five-minute diagnosis, not with buying parts. Dry the head and the arm, watch for a minute, and note whether the water comes from the face or the connection — that one observation tells you whether you need a washer, tape, or a vinegar soak, and it stops you buying parts you do not need. Then try the simplest fix first: tighten the head by hand and give it a quarter-turn. If that stops the drip, you are done in two minutes. If it does not, replace the washer and re-tape the thread — the two together fix nine out of ten leaks, and the whole job takes 15 minutes.
And once the showerhead is sorted, the next leak to check is the tap: our drain and leaky faucet guide fixes a dripping tap with the same washer-and-tape skills, and you can browse every repair idea on the Home Fixes category page.
Frequently Asked Questions
Why does my showerhead drip after I turn the water off?
A showerhead holds water inside it after the shower is off, and that water drains out of the nozzles for a few minutes — that is normal and not a leak. A real leak keeps dripping for more than 10 minutes, or drips constantly even hours later. If it stops within a few minutes, the head is just emptying; if it keeps going, the washer is worn or the connection seal has failed, and steps 5 and 6 will fix it.
How much water does a leaking showerhead waste?
A showerhead dripping once a second wastes around 11,000 litres of water a year — roughly 30 litres a day, or three full buckets every day, going straight down the drain. A faster drip wastes more: two drops a second is about 22,000 litres a year. The water is also heated water in many homes, so a leak wastes energy as well as water, which is why a $2 washer is one of the best-value repairs in the house.
Can I fix a leaky showerhead without turning off the water?
Yes. The showerhead is above the tap, so no water flows to it once the shower is turned off — you do not need to shut off the water supply to the house. Just make sure the shower tap is fully off before you unscrew the head, and keep a towel under the joint to catch the water left inside the head. Only the wall valve or pressure valve jobs in idea 12 need the water supply turned off, and those are plumber's work.
How often should I clean my showerhead?
In a hard-water home, soak the showerhead in white vinegar every 6 months, or sooner if the spray starts going sideways or some nozzles stop working. In a soft-water home, once a year is enough. A quick monthly check is worth doing too: rub the rubber nozzles with your thumb while the water runs, and clear any blocked nozzle with a pin. Regular cleaning stops the limescale build-up that forces water sideways and makes the head leak.

Comments (0)
Post a Comment