Look at your bathroom floor and ask yourself a question: are the tiles actually old, or is it just the grout? In most homes it is the grout. The tiles themselves are usually fine — glazed ceramic barely ages at all — but the grout lines between them collect soap scum, hard-water minerals, dust and, in the shower, a thin film of mould. Those lines turn grey, yellow or black, and because they frame every tile, the whole floor looks tired and dirty no matter how often you mop.
You can clean grout and make old tiles look new again in one afternoon, for about $14, without replacing a single tile. The trick is to treat the grout, not the tile: a simple baking soda paste lifts most of the staining, a stiff brush does the work your mop never could, and a bottle of grout sealer at the end keeps the lines bright for a year or more. Here are 12 ideas, starting with the two checks that stop you damaging your tiles, then the 5-step method itself.
Quick Answer
Dirty grout is usually staining, not damage: a baking soda paste, scrubbed with a stiff brush, lifts most discolouration in 10 minutes. For stubborn stains, use hydrogen peroxide (3%) or an oxygen bleach soak — never mix bleach with vinegar or ammonia. Rinse, dry, then seal the grout; sealed grout stays bright for a year or more.
Key Takeaways
- Grout is usually dirty, not damaged — the original colour is still underneath the stains.
- A baking soda paste and a stiff brush clean most grout in about 10 minutes per section.
- Hydrogen peroxide or oxygen bleach handles stubborn stains; never mix bleach with vinegar or ammonia.
- Tiles look new again once the grout lines are bright — clean the tiles after the grout, not before.
- Seal dry grout and it stays bright for a year or more, so the job only needs doing once a year.
Table of Contents
Know Your Grout Before You Clean It
Grout cleaning goes wrong in exactly one way: using the wrong cleaner on the wrong surface. Two minutes of checking first saves you from etching a stone tile or dissolving a grout line you meant to save.
1. Find out if your grout is sanded or unsanded
Run your fingertip along a grout line. If it feels slightly rough and gritty, it is sanded grout — the kind used on floors, where the joints are usually 3 mm or wider. If it feels smooth, it is unsanded grout — the kind used on walls and narrow joints. This matters because sanded grout is tougher and can take a stiff brush, while unsanded grout is softer and needs a lighter touch: a nylon grout brush or an old toothbrush, never a wire brush, which will gouge it and scratch the glaze off the tiles next to the line. If you are not sure which type you have, treat it as unsanded and be gentle; the paste still works, it just takes an extra pass.
2. Check your tiles — natural stone hates acid
Look at your tiles before you pick a cleaner. Glazed ceramic and porcelain tiles — the shiny, smooth kind in most bathrooms and kitchens — can handle almost any household grout cleaner. Natural stone tiles (marble, travertine, limestone, slate) cannot: vinegar, lemon juice and any acidic cleaner will etch the surface and leave dull patches that no amount of scrubbing fixes. If your tiles are stone, or if you are not sure, skip the vinegar entirely and stick to the baking soda paste and oxygen bleach in this guide — both are safe for stone. Test anything new on one hidden grout line first, behind the door or under the sink cabinet, and wait 10 minutes before you commit to the whole floor.
The 5-Step Grout Cleaning Method
This is the core of the job, and the order matters: dry clean first, then paste, then scrub, then rinse, then seal. Do a small section at a time — about one square metre — so the paste never dries on the tiles before you scrub it. A typical small bathroom floor takes 60 to 90 minutes from start to finish.
3. Sweep and dry-brush the lines first
Sweep the floor or wipe the wall tiles with a dry cloth first, then run a dry stiff brush along every grout line. This sounds like a wasted step, but it is not: loose dust and grit in the grout act like sandpaper when you add water and scrub, and they dull the tile glaze around the lines. The dry brush also shows you what you are really dealing with — the lines that stay dark after a dry brush are stained grout, while the lines that lighten up were just dusty. Put on rubber gloves now, open a window or switch on the extractor fan, and gather your kit before you start: baking soda, a spray bottle of water, a stiff nylon grout brush or old toothbrush, a bucket, clean rags and a grout sealer pen or small bottle ($5–$8) for the final step.
4. Make the baking soda paste and let it sit for 10 minutes
Mix three parts baking soda with one part water in a small bowl until you have a thick paste, about the consistency of toothpaste — for one square metre of floor you need roughly 4 tablespoons of baking soda and a little over 1 tablespoon of water. Spread the paste along the grout lines with your fingertip or an old toothbrush, pressing it into the line rather than smearing it across the tile. Then leave it alone for 10 minutes. The waiting is the work: the paste softens the soap scum and mineral deposits so the brush can lift them instead of grinding them deeper. While you wait, paste the next section, so you always have one section soaking while you scrub the last one. If the paste dries out and turns powdery, mist it lightly with the spray bottle — a dried paste does nothing, a damp one keeps working.
5. Scrub along the lines, not across them
Scrub with short, firm strokes that run along the grout line, not across it. Scrubbing across the line pushes dirt onto the tile and wears the grout edge unevenly; scrubbing along it drives the brush bristles down into the joint where the dirt actually sits. Use the grout brush for floor lines and the old toothbrush for wall tiles and corners, where the brush head is too wide to reach. Spend about 2 minutes per metre of grout line, and do not press so hard your arm aches: steady, even strokes beat brute force, and a brush used gently lasts the whole bathroom instead of splaying out after one wall. Wipe the dirty paste away with a damp rag as you go, so you can see which lines are clean and which need a second pass.
6. Rinse twice and let the grout dry fully
Rinse the section with clean water and a rag, then rinse it a second time. The second rinse matters more than the first: baking soda left in a grout line dries to a white haze that looks almost as bad as the dirt you just removed, and it attracts moisture and new dirt. Then let the grout dry completely before you judge the result. Wet grout always looks darker than dry grout, so lines that look grey while damp often dry to a clean light grey or white. Give a floor at least 2 hours and a shower wall at least 4 hours before deciding a line needs a second treatment; if you seal damp grout, the sealer traps the moisture and turns milky, which is why this step has no shortcut.
7. Seal the grout so it stays bright
Sealing is the step most people skip, and it is the reason their grout is dirty again in a month. Unsealed grout is porous — it drinks in every splash of soapy water and holds it. A grout sealer (a small bottle with a brush applicator, $5–$8, or a sealer pen for narrow lines) coats the surface so water beads on it instead of soaking in. Brush it along the dry grout lines only, wipe any excess off the tiles within 5 minutes, and let it cure for 24 hours before the shower or floor gets wet. Test it: splash a few drops on a sealed line — they should bead up; if they soak in and darken the grout, add a second coat. Sealed floor grout stays bright for about a year, sealed shower grout for 6 to 12 months — then repeat the water test and reseal when it fails.
Stains That Won't Budge
The paste and brush handle most grout, but two kinds of stain need something stronger: the yellow-grey discolouration that builds up over years, and the black mould spots in the shower. Both are fixable without replacing the grout — they just need a different chemical and a little more patience.
8. Try hydrogen peroxide (3%) on grey or yellow stains
If a line is still grey or yellow after the paste and a second scrub, spray it with ordinary 3% hydrogen peroxide — the brown-bottle kind from the pharmacy, about $2 — and let it sit for 10 minutes before scrubbing again. Hydrogen peroxide is a mild oxidiser: it breaks down the organic stains that baking soda cannot lift, and it is safe on glazed ceramic, porcelain and most stone tiles. It also disinfects as it works, which is why it is a good choice for kitchen grout near food preparation. Never mix hydrogen peroxide with vinegar in the same step, and never mix any bleach product with vinegar or ammonia, which releases toxic chlorine gas. One cleaner at a time, rinsed off in between, is the only safe rule. If the stain is still there after the peroxide pass, repeat it once more before moving on to the soak below.
9. Use an oxygen bleach soak for mouldy shower grout
Black spots in shower grout are usually mould sitting on the surface, and an oxygen bleach soak — sodium percarbonate, sold as OxiClean or any store-brand "oxygen bleach", about $4 a tub — is the most effective safe way to remove it. Mix 2 tablespoons of the powder into 500 ml of warm water, brush it along the mouldy lines, and leave it for 30 minutes; for badly stained lines, soak a strip of rag or paper towel in the solution, lay it over the grout and leave it for an hour. Scrub, rinse twice, and let it dry. Oxygen bleach is safe for coloured grout and for septic systems, unlike chlorine bleach, which can lighten coloured grout unevenly and damage the grout surface over time. If the black spots are still there after two soaks, the mould may be growing behind the grout — that is a job for re-grouting, not more cleaning, and idea 11 below covers it. For a full guide to which natural cleaners are safe where, see our natural DIY cleaners guide — what works and what does not.
Make the Tiles Themselves Look New
Once the grout lines are bright, the tiles suddenly look different — and usually better than you expected. Two finishing touches complete the transformation, and both are quick.
10. Wash the tiles after the grout, not before
Clean the tiles only after the grout is done, because scrubbing grout splashes dirty paste across every tile, and washing the tiles first just means washing them twice. For glazed ceramic and porcelain, warm water with a drop of dish soap is enough — wipe in circles with a microfibre cloth, then buff dry with a second cloth, and the glaze shines like new. For a dull film that soap will not shift, usually hard-water scale on shower walls, wipe the tiles with a 50/50 mix of white vinegar and water, leave it for 5 minutes and rinse — but only on glazed ceramic or porcelain, never on natural stone. The dry buff is the part that makes the difference: wet tiles always look streaky, while a 2-minute buff with a dry microfibre cloth leaves a shine that reads as "new tiles" from across the room.
11. Re-caulk the corners and replace cracked grout lines
Look at the corners where the wall meets the bath, the shower tray or the floor. If the sealant there is cracked, peeling or black, no amount of cleaning will fix it — it needs replacing, and it takes 30 minutes. Cut the old sealant out with a utility knife, clean the gap, and run a smooth bead of silicone sealant ($4 a tube) along it, smoothing it with a wet fingertip. The same applies to any grout line that is cracked, crumbling or missing chunks: rake out the loose material with a grout saw or an old screwdriver, vacuum the dust, and press fresh ready-mixed grout ($6 a tub) into the gap with a fingertip, wiping the excess off the tiles before it dries. Fresh caulk and fresh grout in just the worst two or three spots can make a whole bathroom look renovated — it is the highest-impact $10 in this entire guide.
12. Keep it clean with a 2-minute weekly wipe
The whole job only needs doing properly once a year if you do one tiny habit: a 2-minute wipe once a week. After your usual bathroom clean, run a dry microfibre cloth along the floor grout lines, or squeegee the shower walls after the last shower of the week. That removes the soap film before it hardens into the stain you just spent an afternoon removing. In the shower, the single best habit is a 30-second squeegee after each shower — it takes the water off the tiles before the minerals in it can dry onto the grout. Once the tiles look new, keep the rest of the room matching — see our guide to organizing a small bathroom with no storage — and browse all our cleaning guides on the Cleaning category page.
A Worked Example: A Small Bathroom Floor for $14
Here is what the whole job costs for a typical small bathroom floor (about 4 square metres), buying everything new:
| Item | Cost | What it does |
|---|---|---|
| Baking soda (500 g box) | $2 | The cleaning paste |
| Hydrogen peroxide 3% (250 ml) | $2 | Stubborn yellow-grey stains |
| Oxygen bleach powder (small tub) | $4 | Mouldy shower grout soak |
| Grout brush + old toothbrush | $0 | Use a brush you already own |
| Grout sealer (small bottle) | $6 | Keeps the lines bright for a year |
| Spray bottle + rags | $0 | From under the sink |
| Total | $14 | About 90 minutes, once a year |
That $14 total assumes you buy the peroxide and the oxygen bleach as well as the sealer. If your grout only needs the paste and the sealer — which is true for most floors that are dirty rather than mouldy — the cost drops to $8. The only real cost here is the 90 minutes, and most of that is waiting for the paste and the sealer to do their work.
Your Clean-Grout Checklist
Work through this list in order — check first, then clean, then seal — and tick each step off as you finish it:
- ☐ Feel the grout: sanded (rough) or unsanded (smooth) — and never use a wire brush
- ☐ Check the tiles: natural stone means no vinegar or acid cleaners, ever
- ☐ Test your cleaner on one hidden grout line and wait 10 minutes
- ☐ Sweep and dry-brush every grout line before adding any water
- ☐ Mix the baking soda paste (3 parts soda, 1 part water) and spread it into the lines
- ☐ Let the paste sit for 10 minutes, then scrub along the lines, not across them
- ☐ Rinse twice with clean water, changing the water when it turns cloudy
- ☐ Let the grout dry fully — 2 hours for floors, 4 hours for shower walls
- ☐ Treat stubborn stains with 3% hydrogen peroxide, or an oxygen bleach soak for mould
- ☐ Seal the dry grout lines and let the sealer cure for 24 hours
- ☐ Wash and buff the tiles dry with a microfibre cloth
- ☐ Do the water-bead test — if water soaks in, add a second coat of sealer
Where Should You Start?
Start with the test line: pick one hidden grout line behind the bathroom door, spread the baking soda paste on it, wait 10 minutes and scrub. If the line comes back bright — and it usually does — you know the method works on your grout, and you have the confidence to do the whole room.
Then do the floor before the walls, and the worst room first. A small bathroom floor takes about 90 minutes including drying time, and seeing those lines turn bright is the motivation to do the shower next. Finish by sealing the grout the same day, while it is clean and dry — sealed grout stays bright for a year.
Mould on grout is a moisture problem first and a cleaning problem second: if the black spots keep coming back, the bathroom is staying damp. Our guide to stopping mould in a small bathroom shows how to stop it coming back — find every patch, remove it in about 30 minutes, and keep it away with a $9 fix.
Frequently Asked Questions
Can you really make old grout look new again without replacing it?
Yes, in most cases. The discolouration on old grout is usually surface staining — soap scum, mineral deposits and dust sitting in the pores — and the original grout colour is still underneath. A baking soda paste and a stiff brush remove that staining and reveal the original colour. Only grout that is cracked, crumbling or stained all the way through by mould needs replacing, and even then you only replace the damaged lines, not the whole floor.
Is it safe to use vinegar on grout?
On glazed ceramic or porcelain tiles with cement grout, diluted vinegar used occasionally is safe, but it is acidic and can slowly erode grout if used every week, so the baking soda paste is a better regular cleaner. Never use vinegar on natural stone tiles such as marble or travertine — it etches the surface permanently. And never mix vinegar with bleach or with hydrogen peroxide — use one cleaner at a time and rinse in between.
How long does grout sealer last?
Sealed floor grout stays protected for about a year, and sealed shower grout for 6 to 12 months, because showers get wet every day. Test it with the water-bead test: splash a few drops of water on a grout line — if they bead up, the sealer is still working; if they soak in and darken the grout, it is time to clean and reseal.
Why does my grout get dirty again so fast?
Because unsealed grout is porous — it absorbs every splash of soapy water, every speck of dust and every drop of hard water, and holds it in the pores where a mop cannot reach. The fix has two parts: seal the grout so water beads on the surface instead of soaking in, and do a 2-minute dry wipe of the grout lines once a week so soap film never hardens into a stain. With those two habits, a deep clean once a year is enough.

Comments (0)
Post a Comment