A small washing machine works harder than almost anything else in a small home. It runs three or four loads a week in a tight space, often with the door shut between washes, and it slowly fills with the things you cannot see: detergent residue, lint, limescale and the damp film that turns into black mould and a sour smell. The worst part is that a dirty machine makes your laundry dirtier — clothes come out smelling musty even when they went in clean, and that is the first sign the machine itself needs a wash.
How to clean a small washing machine comes down to one 45-minute routine a month: a hot vinegar cycle, a baking soda cycle, a wipe of the seal and drawer, and a quick filter clean. It costs about $4 a year, needs no special products, and it stops smells, mould and the breakdowns that come from a clogged filter or a scaled-up heater. Do it on the first Saturday of the month and the machine stays as clean as the clothes it washes.
Quick Answer: Run one empty hot cycle at 60°C with 2 cups (500 ml) of white vinegar, then a second with half a cup (100 g) of baking soda, once a month. Clean the filter and detergent drawer, wipe the door seal dry after every wash, and leave the door ajar. The routine takes 45 minutes and costs about $4 a year.
Key Takeaways
- One empty 60°C cycle with 2 cups of white vinegar a month dissolves limescale and kills the smell at its source.
- The filter traps coins, hair and lint — clean it monthly or the machine drains slowly and stops mid-cycle.
- Wipe the rubber door seal dry after every wash, because mould grows in the folds within days.
- Use less detergent than you think: too much leaves residue that feeds smells and mould.
- Leave the door ajar between washes so the drum dries instead of staying damp and musty.
Table of Contents
Run the Monthly Deep Clean
The monthly deep clean is the core of washing machine care, and it is five steps in order. Set aside 45 minutes, run it on an empty machine, and do the steps in this order — the hot cycle first, then the parts you can only reach once the drum is clean and warm.
1. Run an empty hot cycle with 2 cups of white vinegar
Pour 2 cups (500 ml) of plain white vinegar straight into the empty drum, not into the detergent drawer, and run the hottest cycle your machine offers — 60°C on most small machines, 90°C if yours goes that high. The hot water and acid dissolve limescale on the heater and drum, and the vinegar kills the bacteria that cause the sour smell. Do not add laundry, and do not add detergent: the point is to clean the machine, not a load. When the cycle ends, open the door and you will already notice the difference — the drum smells fresh instead of stale, and any grey film on the rubber seal will have loosened.
2. Follow with a baking soda cycle to finish the job
Once the vinegar cycle has finished, sprinkle half a cup (100 g) of baking soda directly into the empty drum and run a second hot cycle, again at 60°C. The baking soda neutralises any vinegar left behind and scrubs away the loosened grime as the drum spins, so the inside of the machine ends up clean and odour-free rather than just smelling of vinegar. Two cycles back to back take about 40 minutes in total on a small machine, and that is the whole deep clean — no scrubbing, no special cleaner, and no taking the machine apart.
3. Wipe the drum, the seal and the door while they are warm
As soon as the second cycle ends, wipe the inside of the drum with a dry microfibre cloth to catch any loosened residue before it dries back on. Then pull back the folds of the rubber door seal — the grey ring around the door opening — and wipe inside every fold with the cloth, because that is where black mould hides. A small machine's seal has two or three folds, and a fingertip wrapped in the cloth reaches all of them in under a minute. If you see black spots, dab them with a cloth dipped in undiluted white vinegar, leave it for 10 minutes, then wipe again. Never use bleach on the seal: it weakens the rubber over time and makes it crack.
4. Soak the detergent drawer and scrub the drawer housing
Pull the detergent drawer all the way out — most small machines have a small tab or button in the middle you press to release it — and soak it in a bowl of hot water with a splash of white vinegar for 15 minutes. While it soaks, wipe the empty drawer housing with a damp cloth, and use an old toothbrush to scrub the little jets and corners where detergent crusts over. Rinse the drawer, dry it, and slide it back in. A drawer that is caked in old detergent does not just look dirty: it feeds mould into every wash and stops the detergent dissolving properly, so your clothes get less clean with every load.
Clean the Parts Most People Forget
Three parts of a small washing machine almost never get cleaned, and all three cause the breakdowns people blame on the machine being old or cheap. They take five minutes between them, and they are the difference between a machine that lasts ten years and one that gives up after three.
5. Clean the filter every month — it is where the blockages live
The filter sits behind a small flap at the bottom front of the machine, usually on the right. Put a shallow tray and an old towel under it first, because a little water always comes out, then unscrew the filter cap slowly — anticlockwise — and pull the filter out. You will find coins, hair, buttons, lint and the odd sock: pull it all off, rinse the filter under the tap, and wipe the housing inside with a cloth before screwing it back in. If your machine drains slowly, stops mid-cycle with water still inside, or makes a rattling noise during the spin, a clogged filter is the most likely cause, and cleaning it fixes the problem in two minutes.
6. Check the drain hose and the water inlet filters twice a year
Pull the machine out just far enough to see the drain hose at the back — about 15 cm is enough — and check that it is not kinked, squashed flat against the wall, or hanging lower than the machine's drum, because a kinked or drooping hose is why some small machines leave water in the bottom. Also check the two small mesh filters where the inlet hoses join the machine: turn off the water, unscrew the hoses by hand, and rinse the little mesh screens under the tap. In hard-water areas they clog with limescale in six months, and a clogged inlet filter is why a machine takes forever to fill or shows a water-supply error. Put everything back finger-tight — never force the hoses with a wrench, or you will crack the plastic fitting.
7. Level the feet so the machine stops walking across the floor
A small washing machine that shakes, bangs or creeps across the floor during the spin cycle is usually not broken — it is not level. Put a spirit level on top of the machine, front to back and side to side, and turn the adjustable feet underneath until the bubble sits in the middle: clockwise to lower a foot, anticlockwise to raise it, then tighten the lock nuts by hand. All four feet must touch the floor firmly, with no rocking when you push the top corner. A level machine spins quieter, wears its bearings out far more slowly, and stops thumping against the wall at 2 a.m. — and on a wooden floor, a 40 cm square anti-vibration mat under the machine, about $8, makes the difference even bigger.
Stop Smells and Mould Before They Start
Cleaning fixes a smelly machine, but three small habits stop the smell coming back — and they cost nothing at all. The rule behind all of them is simple: mould and bacteria need damp, darkness and leftover detergent, so take away one of those three and they cannot grow.
8. Leave the door ajar after every single wash
The single most effective habit is also the simplest: after every wash, leave the door open a few centimetres, and pull the detergent drawer out a centimetre too. A closed machine stays damp inside for hours, and that damp, dark drum is exactly where mould grows — which is why a machine that is always shut smells musty within a week. An open door lets the drum and the seal dry out between washes, and it costs nothing. If you have small children or pets, wedge the door with a folded cloth instead of leaving it wide open, so little hands and paws cannot climb in.
9. Use less detergent than the box tells you to
Most people use about twice as much detergent as a small load needs, and the extra does not make clothes cleaner — it leaves a sticky residue inside the drum, the pipes and the seal, and that residue is food for the bacteria that cause the smell. For a small machine, one tablespoon of liquid detergent, about 15 ml, is enough for a normal load, and half that is enough for a lightly soiled one. If your clothes come out feeling stiff or the machine smells of detergent after a wash, you are using too much. Switch to a liquid rather than a powder in a cold-water wash, because powder does not always dissolve fully below 30°C and leaves grit in the drawer and the seal. Our natural DIY cleaners guide explains why vinegar and baking soda work so well as cleaners — the same two ingredients do the monthly machine clean in this post.
10. Take the laundry out promptly and dry the seal
Wet laundry left in a closed drum for more than an hour starts to smell, and the damp it leaves behind feeds the mould in the seal. Take each load out as soon as the cycle ends, give the drum a quick wipe with a dry cloth if you have one handy, and run a finger along the bottom fold of the seal to dry it — that fold is the one place water always pools. This takes 30 seconds and it is the habit that makes the monthly deep clean a quick refresh instead of a rescue job. If you do forget a load overnight, run it again on a short rinse cycle rather than drying it as it is: the smell is bacteria, and drying will only set it into the fabric.
Small-Machine Care: Portable and Compact Washers
Compact and portable washing machines — the kind that fit in a flat, a caravan or a tiny laundry corner — need two extra bits of care that a full-size machine does not, because they move, they drain differently, and they often sit unused between washes.
11. Drain a portable machine fully between uses
A portable washer that connects to a tap and drains into a sink holds water in its hoses and pump after every wash, and that standing water goes stale in a few days. After the last load, run a 1-minute spin with the drain hose in the sink, then lift the hose and let the last of the water out before you coil it up. If you are putting the machine away for a week or more — in a cupboard, for example — run the monthly vinegar cycle first, then leave the lid open and the drain hose hanging down so every last drop escapes. A machine stored damp grows mould in the pump, and the first wash after storage will smell of it.
12. Give a compact machine space to breathe and spin
Small machines vibrate more than big ones because the drum is lighter, so give yours at least 2 cm of clear space on every side — never wedge it tight between a wall and a cupboard, or the vibration will wear the feet and the hoses. Keep the top clear too: a stack of detergent bottles on top of a spinning machine falls off, and the weight makes the machine rock. And never overload it: a compact machine holds about 5 to 6 kg of dry laundry, which is roughly one week's clothes for one person, and a load heavier than that strains the motor, leaves clothes half-clean, and shakes the machine across the floor. Wash little and often — two small loads beat one stuffed one every time.
What Cleaning and Maintaining Your Washer Costs
Here is what a year of washing machine care costs if you buy the basics new — and you probably have two of the three already:
| Item | Cost |
|---|---|
| White vinegar, 1 litre (12 monthly cycles) | $2 |
| Baking soda, 500 g (12 monthly cycles) | $1 |
| Microfibre cloths, pack of 3 | $1 |
| Total per year | $4 |
The honest version: the vinegar and baking soda are the only things you will actually use up, and a litre of vinegar and a 500 g box of baking soda last the whole year. The optional extras — a pack of washing-machine cleaner tablets for about $6, or an anti-vibration mat for about $8 — are nice to have but not needed. Compare that with the cost of the problems this routine prevents: a plumber call-out for a clogged filter or a blocked drain hose starts at $60, and a machine replaced three years early because of limescale costs hundreds. Four dollars a year is the cheapest insurance a small home owns.
Your Washing Machine Care Checklist
Work through this list in order and tick each step off as you finish it:
- Run an empty 60°C cycle with 2 cups (500 ml) of white vinegar in the drum
- Run a second empty 60°C cycle with half a cup (100 g) of baking soda
- Wipe the drum dry and clean inside every fold of the rubber door seal
- Soak the detergent drawer in hot water and vinegar, scrub the housing with a toothbrush
- Unscrew the filter, remove coins and lint, rinse it and screw it back in
- Check the drain hose for kinks and rinse the inlet mesh filters
- Level the machine with a spirit level so all four feet touch the floor
- Switch to 1 tablespoon of liquid detergent per load
- Leave the door ajar and the drawer out a centimetre after every wash
- Take each load out as soon as the cycle ends and dry the bottom seal fold
- Drain a portable machine fully before storing it away
- Repeat the deep clean on the first Saturday of every month
Where Should You Start?
Start with the two hot cycles, not with the filter or the drawer. Pour 2 cups of white vinegar into the empty drum, run it at 60°C, then follow with half a cup of baking soda on a second hot cycle — that alone fixes most smells and a lot of the limescale, and it takes 40 minutes while you do something else. Then, while the drum is still warm, wipe the seal and pull the filter out: those two five-minute jobs are the ones that stop the next breakdown. Do the whole routine on the first Saturday of the month and put it on the calendar, because a machine you clean monthly never gets bad enough to need rescuing.
And once the machine is clean, the room around it deserves the same treatment: our small laundry room organization ideas show how to give every bottle and basket a home in the same small space, and you can browse every cleaning idea on the Cleaning category page.
The washing machine is not the only small appliance that needs a monthly deep clean — the dishwasher gets the same treatment: see how to clean a small dishwasher and stop bad smells.
Frequently Asked Questions
Can I use vinegar and baking soda together in a washing machine?
Not at the same time. Vinegar is an acid and baking soda is an alkali, so mixed together they cancel each other out and do very little cleaning. Use them in separate cycles, as this post describes: vinegar first on a hot cycle to dissolve limescale and kill bacteria, then baking soda on a second hot cycle to neutralise the vinegar and lift away the loosened grime. Two separate cycles do the job properly; one mixed cycle does almost nothing.
How often should I clean a small washing machine?
Run the full deep clean — the two hot cycles, the seal wipe, the drawer soak and the filter clean — once a month, on the first Saturday if you want a routine you will actually keep. If you wash every day, or you live in a hard-water area, do the vinegar cycle every two weeks instead. The daily habits — leaving the door ajar, using less detergent and taking laundry out promptly — are every wash, not monthly, and they are what keep the machine fresh between deep cleans.
Why does my washing machine smell even after I clean it?
The smell usually lives somewhere the cleaning cycle did not reach: the folds of the rubber door seal, the detergent drawer housing, or the drain filter. Pull the seal folds back and wipe inside them, soak the drawer and scrub the housing with a toothbrush, and unscrew the filter to clear the trapped lint and coins. If the smell survives all three, run the vinegar cycle at 90°C instead of 60°C, and check that the drain hose is not kinked or drooping — standing water in the hose smells worse than anything in the drum.
Is it safe to clean a washing machine with vinegar if I rent?
Yes. White vinegar and baking soda are the most renter-friendly cleaners there are: they do not damage the drum, the seal or the hoses, they leave no residue, and they cost about $4 a year. Do not use bleach on the rubber seal, because it weakens the rubber over time, and never pour a drain cleaner or a limescale remover meant for kettles into the machine — those are too harsh for the seals and the pump. If your machine is supplied by your landlord and the problem is a fault rather than dirt — it will not drain, or it leaks — report it to the landlord instead of taking the machine apart.

Comments (0)
Post a Comment